Solved

SG300-10PP  switch - will this be suffice for a core router in a satelite office

Posted on 2015-02-24
3
257 Views
Last Modified: 2015-02-26
I'm looking to install a core router in a remote site that is currently setup as one be 16bit LAN, it has some managed switched already but in un-manged mode (not configured).    I'm considering putting an SG300-10PP 10-Port Gigabit Managed Switch in as the core.  In the specs it shows layer 3 capable.   I'm looking to split the network up into VLAN's, one for PC's, Servers, Printers, and possibly Wireless.   I'm about %75 in know of how to do this but I'm not sure if this switch will the right fit.  Has anyone else used these models for similar functions or suggestions?   Thanks!
0
Comment
Question by:sugadmin
  • 2
3 Comments
 
LVL 14

Accepted Solution

by:
JAN PAKULA earned 500 total points
ID: 40629589
yes that will work - we are using some 500 ones (they can stack) and some 300

@vlans - if your network is small (less then 50 devices) don't use them -  keep it simple
0
 

Author Comment

by:sugadmin
ID: 40630625
Great, Thanks for the advice JAN PAKULA.    This site is exactly 101 devices.  
I'll look at the 500 series also, The ability to stack will also provide some redundancy I suppose.

Right now with one big LAN and un-managed switches we have the ability to throw in any type of "dumb-switch" anywhere to fix an issue.  If we have a configured core and it goes down it's best to have a backup or stack?  I need to do more research obviously.
0
 
LVL 14

Expert Comment

by:JAN PAKULA
ID: 40633734
stack would be better as you could have 10Gb between them - but cost  of 500x is to be taken into account :-)

http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/Sx500/quick_start/en/500_Series_QSG_En.pdf

##########
Possible Stack Configuration Stack Ports Speed
SG500Xs in Native Stacking mode. 1G/10G or 1G/5G


Sx500s in Native Stacking mode. 1G/5G (default) or 1G Copper/
SFP (Combo)

SG500Xs and Sx500s in Basic
Hybrid mode, where either device
can serve as master, backup, or slave.
1G/5G

SG500Xs and Sx500s in Advanced
Hybrid mode, without backup.
• Master: SG500X
• Slaves: Either type of device
1G/5G

SG500Xs and Sx500s in Advanced
Hybrid mode.
• Master: SG500X
• Backup: SG500X
• Slaves: Either type of device
1G/5G

############
SG500XGs in Native Stacking mode. 10G copper/SFP+
SG500XGs and SG500Xs in
Advanced Hybrid XG mode, where
either device can serve as master,
backup, or slave.
SG500X: SFP+
SG500XG:10G copper/SFP+
0

Featured Post

Announcing the Most Valuable Experts of 2016

MVEs are more concerned with the satisfaction of those they help than with the considerable points they can earn. They are the types of people you feel privileged to call colleagues. Join us in honoring this amazing group of Experts.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Creating an OSPF network that automatically (dynamically) reroutes network traffic over other connections to prevent network downtime.
Data center, now-a-days, is referred as the home of all the advanced technologies. In-fact, most of the businesses are now establishing their entire organizational structure around the IT capabilities.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

839 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question