BR_
asked on
How do I redirect the traffic for one IP address on one subnet to another IP address on another subnet using Cisco 1921 Routers
How do I redirect traffic for one IP address on one subnet to an IP address on another subnet.
Main Network
192.168.1.0 255.255.255.0 192.168.1.1
Cisco 1921 Router
10.10.10.1 255.255.255.0
|
|
10.10.10.2 255.255.255.0
Cisco 1921 Router
192.168.4.1 255.255.255.0 192.168.4.1
Remote Network
Traffic sent by 192.168.4.150 server needs to be redirected to 192.168.1.7 on the Main Network.
Main Network
192.168.1.0 255.255.255.0 192.168.1.1
Cisco 1921 Router
10.10.10.1 255.255.255.0
|
|
10.10.10.2 255.255.255.0
Cisco 1921 Router
192.168.4.1 255.255.255.0 192.168.4.1
Remote Network
Traffic sent by 192.168.4.150 server needs to be redirected to 192.168.1.7 on the Main Network.
On Main network Cisco 1921 router enter following:
Router(config)#ip route 192.168.4.0 255.255.255.0 10.10.10.2
On Remote network Cisco 1921 router enter following:
Router(config)#ip route 192.168.1.0 255.255.255.0 10.10.10.1
Regards!
Router(config)#ip route 192.168.4.0 255.255.255.0 10.10.10.2
On Remote network Cisco 1921 router enter following:
Router(config)#ip route 192.168.1.0 255.255.255.0 10.10.10.1
Regards!
ASKER
The two networks are connected via Metro Ethernet and can communicate with each other perfectly.
The two Cisco 1921 routers are configured with:
Main Network Cisco router: ip route 192.168.4.0 255.255.255.0 10.10.10.2
Remote Network Cisco router ip route 192.168.1.0 255.255.255.0 10.10.10.1
The problem I have is getting the traffic for 192.168.4.190 at our second location to go directly to 192.168.1.7.
I have uploaded a diagram.
Metro.pdf
The two Cisco 1921 routers are configured with:
Main Network Cisco router: ip route 192.168.4.0 255.255.255.0 10.10.10.2
Remote Network Cisco router ip route 192.168.1.0 255.255.255.0 10.10.10.1
The problem I have is getting the traffic for 192.168.4.190 at our second location to go directly to 192.168.1.7.
I have uploaded a diagram.
Metro.pdf
ASKER
I found the solution to my problem. I was using my source address. I should have been using my destination address.
I entered the route using my destination address and was able to connect.
Thank you all for your input.
I entered the route using my destination address and was able to connect.
Thank you all for your input.
Excellent
ASKER
I've requested that this question be closed as follows:
Accepted answer: 0 points for BR_'s comment #a40663971
for the following reason:
My mistake. When I created my route I used the source address instead of the destination address. When I changed it to the destination address it worked.
Accepted answer: 0 points for BR_'s comment #a40663971
for the following reason:
My mistake. When I created my route I used the source address instead of the destination address. When I changed it to the destination address it worked.
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
Sorry - I thought I had closed this question.
If yes, you will need to implement routing between the two networks.
By remote network, do you mean outside your firewall, over the internet or different site.
If the networks are behind the same firewall
- On the 1921 router, type the following route statement
Router>en
Router#conf t
Router(config)#ip route 192.168.1.0 255.255.255.0 192.168.4.1
On the remote router
Router>en
Router#conf t
Router(config)#ip route 192.168.4.0 255.255.255.0 192.168.1.1
Please provide a diagram and answer to the questions. I have a feeling the remote network is behind a different firewall. if so there's a lot more to it than described above