waref86
asked on
Calling Forward to Destination with specific format
Hi,
Anyone can help me with the below, I got this information from a telecommunication company, what do I have to do to send the number as per his request
You are sending the originating Number (A#) as “0” and the Destination Number as “94888231”.
While it should be as follows:
The originating Number (A#), should be 96611510XXXX format.
The Destination Number should be “0114777231”.
Regards
Anyone can help me with the below, I got this information from a telecommunication company, what do I have to do to send the number as per his request
You are sending the originating Number (A#) as “0” and the Destination Number as “94888231”.
While it should be as follows:
The originating Number (A#), should be 96611510XXXX format.
The Destination Number should be “0114777231”.
Regards
What Sip/VoIP gateway or PBX are you using ? You will need to change the normalization rule on it in order to match the telecom company's request.
ASKER
I'm using Cisco CME 2921, and telecom connected to my CME through Ethernet.
the rule which I have to change is it translation rules for out calls
the rule which I have to change is it translation rules for out calls
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
Hi,
thank you for suggestion, still not working, kindly fine below the debug after applying the translation-rules:
*May 7 10:32:22.931: //3518/270355639660/SIP/Ms g/ccsipDis playMsg:
Received:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 10.65.8.102:5060;branch=z9 hG4bK1E5C5
From: "Reception" <sip:0@10.65.8.102>;tag=AC CA4C8-1615
To: <sip:0114777231@94.77.211. 70>
Call-ID: 2E5D0B7F-F3DB11E4-9665A9E6 -7CC56A7A@ 10.65.8.10 2
CSeq: 101 INVITE
Timestamp: 1430994742
*May 7 10:32:22.931: //3518/270355639660/SIP/Ms g/ccsipDis playMsg:
Received:
SIP/2.0 480 No Routes Found
Via: SIP/2.0/UDP 10.65.8.102:5060;branch=z9 hG4bK1E5C5
From: "Reception" <sip:0@10.65.8.102>;tag=AC CA4C8-1615
To: <sip:0114777231@94.77.211. 70>;tag=ap rqngfrt-mu pl1s20000a 6
Call-ID: 2E5D0B7F-F3DB11E4-9665A9E6 -7CC56A7A@ 10.65.8.10 2
CSeq: 101 INVITE
Timestamp: 1430994742
*May 7 10:32:22.935: //-1/xxxxxxxxxxxx/SIP/Msg/ ccsipDispl ayMsg:
Sent:
ACK sip:0114777231@94.77.211.7 0:5060 SIP/2.0
Via: SIP/2.0/UDP 10.65.8.102:5060;branch=z9 hG4bK1E5C5
From: "Reception" <sip:0@10.65.8.102>;tag=AC CA4C8-1615
To: <sip:0114777231@94.77.211. 70>;tag=ap rqngfrt-mu pl1s20000a 6
Date: Thu, 07 May 2015 10:32:22 GMT
Call-ID: 2E5D0B7F-F3DB11E4-9665A9E6 -7CC56A7A@ 10.65.8.10 2
Max-Forwards: 70
CSeq: 101 ACK
Allow-Events: telephone-event
Content-Length: 0
thank you for suggestion, still not working, kindly fine below the debug after applying the translation-rules:
*May 7 10:32:22.931: //3518/270355639660/SIP/Ms
Received:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 10.65.8.102:5060;branch=z9
From: "Reception" <sip:0@10.65.8.102>;tag=AC
To: <sip:0114777231@94.77.211.
Call-ID: 2E5D0B7F-F3DB11E4-9665A9E6
CSeq: 101 INVITE
Timestamp: 1430994742
*May 7 10:32:22.931: //3518/270355639660/SIP/Ms
Received:
SIP/2.0 480 No Routes Found
Via: SIP/2.0/UDP 10.65.8.102:5060;branch=z9
From: "Reception" <sip:0@10.65.8.102>;tag=AC
To: <sip:0114777231@94.77.211.
Call-ID: 2E5D0B7F-F3DB11E4-9665A9E6
CSeq: 101 INVITE
Timestamp: 1430994742
*May 7 10:32:22.935: //-1/xxxxxxxxxxxx/SIP/Msg/
Sent:
ACK sip:0114777231@94.77.211.7
Via: SIP/2.0/UDP 10.65.8.102:5060;branch=z9
From: "Reception" <sip:0@10.65.8.102>;tag=AC
To: <sip:0114777231@94.77.211.
Date: Thu, 07 May 2015 10:32:22 GMT
Call-ID: 2E5D0B7F-F3DB11E4-9665A9E6
Max-Forwards: 70
CSeq: 101 ACK
Allow-Events: telephone-event
Content-Length: 0
Your configuration is still not correct, can you post reception profile configuration along with Call routing translation pattern you're using and the route pattern too.
ASKER
Hi,
Do you mean to separate below each profile alone? and inside dial-peer configure inside translation-rule for called and caling
voice translation profile CHANGE-ME
translate called 1
translate calling 2
Do you mean to separate below each profile alone? and inside dial-peer configure inside translation-rule for called and caling
voice translation profile CHANGE-ME
translate called 1
translate calling 2
ASKER
I forget to mention something, there are a format for outgoing calls and format for incoming calls.
• For outgoing Calls :
The originating Number (A#), should be 96611510XXXX format.
The Destination Number should be 0NXXXXXX (N area code) or 00XXXXXXXXX (for international)
• For incoming Calls:
The Destination Number (B#), should be 011510XXXX Format.
The originating Number (A#), will be 0NXXXXXXX or 00XXXXXXXXXXX Format
and I figure out something, when I'm using a ip phone with extension 0, it shows on SIP calls
From: "Reception" <sip:0@10.65.8.102>;tag=ACCA4C8-1615
any solution please
regards
• For outgoing Calls :
The originating Number (A#), should be 96611510XXXX format.
The Destination Number should be 0NXXXXXX (N area code) or 00XXXXXXXXX (for international)
• For incoming Calls:
The Destination Number (B#), should be 011510XXXX Format.
The originating Number (A#), will be 0NXXXXXXX or 00XXXXXXXXXXX Format
and I figure out something, when I'm using a ip phone with extension 0, it shows on SIP calls
From: "Reception" <sip:0@10.65.8.102>;tag=ACCA4C8-1615
any solution please
regards