Basic Cisco switch configuration.

I'm trying to configure a cisco 3650 switch I have enabled the vlan with IP, net mask and a default gateway however I still cant get any network traffic through the switch.
Is there anything else I need to do, as obviuos I'm not Cisco expert!!

Who is Participating?

[Product update] Infrastructure Analysis Tool is now available with Business Accounts.Learn More

I wear a lot of hats...

"The solutions and answers provided on Experts Exchange have been extremely helpful to me over the last few years. I wear a lot of hats - Developer, Database Administrator, Help Desk, etc., so I know a lot of things but not a lot about one thing. Experts Exchange gives me answers from people who do know a lot about one thing, in a easy to use platform." -Todd S.

NetExpert Network Solutions Pte LtdTechnical SpecialistCommented:
can you post your current switch Running config here and can you explain how this switch is connected with upstream device
Kash2nd Line EngineerCommented:
# show running-config

post here
atorexAuthor Commented:
The switch is attached to a router and several servers attached, the IP scheme is nothing beyound that.
I dont have access to its console from here the switch is currently in another office, I can access it with the Cisco Network Assistant software but that saves the runing configs as a jar.
I will get the configs in a couple hours and post.

Powerful Yet Easy-to-Use Network Monitoring

Identify excessive bandwidth utilization or unexpected application traffic with SolarWinds Bandwidth Analyzer Pack.

atorexAuthor Commented:
Ok here is the runing configs
NetExpert Network Solutions Pte LtdTechnical SpecialistCommented:

the config you pasted here if C2960 switch model. per question, you are trying to configure 3560 switch.

we need your 3560 switch config details and need to know, how this new switch is connected with upstream devices
atorexAuthor Commented:
sorry i have both but am not using the 3650, the correct one is 2960 i ca close this and open a new question with corect device.
NetExpert Network Solutions Pte LtdTechnical SpecialistCommented:

no need to open a new question.. we can continue with this question.

i do see the the switch has proper vlan config and trunk port in place,,,   can you run the below command in upstream router and paste the output here

#sh ip int br | ex una
#sh vlan-switch

Experts Exchange Solution brought to you by

Your issues matter to us.

Facing a tech roadblock? Get the help and guidance you need from experienced professionals who care. Ask your question anytime, anywhere, with no hassle.

Start your 7-day free trial
atorexAuthor Commented:
Unfortunatly the router we have in this small office is an Apple Airport Extreme, we are attempting to add POE pnones so the 2960 was purchased.
Just a small bussiness trying to servive and do small upgrade J.
NetExpert Network Solutions Pte LtdTechnical SpecialistCommented:
I assume that your connectivity looks like below

Workstation/phone -- 2960 switch --- AirPort Extreme -- internet

Who provides the IP address to your workstation/ip phone
atorexAuthor Commented:
Exactly, that is the basic setup and we are using DHCP from the Airport extreme router for IP.
atorexAuthor Commented:
After you veryfying the configurations I had I went trhougt and re wired the connections just brought evrything up and I am able to bring up a phone on POE with DHCP access, I'm also able to attache servers to it and have access from the work stations, thanks so much for hanging in there with me I apreciate the knowledgeble guidance.

It's more than this solution.Get answers and train to solve all your tech problems - anytime, anywhere.Try it for free Edge Out The Competitionfor your dream job with proven skills and certifications.Get started today Stand Outas the employee with proven skills.Start learning today for free Move Your Career Forwardwith certification training in the latest technologies.Start your trial today
Switches / Hubs

From novice to tech pro — start learning today.