Cisco Switch Fiber connection

I have two Cisco switches Cisco WS-C2960X-48FPD-L and I have a fiber line running between the 2 switches it is a Multimode 50 that ends in a patch pannel ,the distance is about 300 meter. I have s SFP-10Gbase-LR in my terabytes ports and  I am using LC to LC Duplex MM50/125 patch cables. I tested the cables I tested the modules the are OK but I cannot get a connection between the two. This is status of the interface and below the configuration of my interface. What can be wrong??
 

Switch#sh int te2/0/1
TenGigabitEthernet2/0/1 is down, line protocol is down (notconnect)
  Hardware is Ten Gigabit Ethernet, address is bcc4.9327.7fb3 (bia bcc4.9327.7fb                                                        3)
  MTU 1500 bytes, BW 10000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive not set
  Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-LR
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out
tonzur40Asked:
Who is Participating?
I wear a lot of hats...

"The solutions and answers provided on Experts Exchange have been extremely helpful to me over the last few years. I wear a lot of hats - Developer, Database Administrator, Help Desk, etc., so I know a lot of things but not a lot about one thing. Experts Exchange gives me answers from people who do know a lot about one thing, in a easy to use platform." -Todd S.

artyom39Commented:
Seems physical layer. Did you check patch cords A and B? A in the one side has to be connected to B another side, and B to A (Rx to Tx). If you checked cable and patch cords, check module compatible with switch.
0

Experts Exchange Solution brought to you by

Your issues matter to us.

Facing a tech roadblock? Get the help and guidance you need from experienced professionals who care. Ask your question anytime, anywhere, with no hassle.

Start your 7-day free trial
tonzur40Author Commented:
Artyom39 -I think we are in the wright path. I swapped the cables and I show the link up on both on my interfaces however I still can not communicate to each other. I cannot ping the switches and I do not have connection between my workstations.
0
artyom39Commented:
What's your SFP model and IOS version ?
0
tonzur40Author Commented:
IOS version 15.0 (2a)EX5 and the module is SFP-10GBase-LR
0
It's more than this solution.Get answers and train to solve all your tech problems - anytime, anywhere.Try it for free Edge Out The Competitionfor your dream job with proven skills and certifications.Get started today Stand Outas the employee with proven skills.Start learning today for free Move Your Career Forwardwith certification training in the latest technologies.Start your trial today
Switches / Hubs

From novice to tech pro — start learning today.

Question has a verified solution.

Are you are experiencing a similar issue? Get a personalized answer when you ask a related question.

Have a better answer? Share it in a comment.