jac1991
asked on
Cisco UC 520 CUE Reload
Hello,
Trying to reload a Cisco UC 520, CUE, only, the CF card went bad, I replaced it.
There were no backups
Using cli, I did a service-module integrated-Service-Engine 0/0 reload and confirm, then service-module integrated-Service-Engine 0/0 session
config
then boot helper
I get bad magic number, see below
I think I have the wrong PKG file, Cisco web site does not have a download for a download specifically for a 520, which is what I need , I think
Any one know where I can get one ?
ServicesEngine boot-loader>
ServicesEngine boot-loader> ?
? - alias for 'help'
boot - boot from specified src
config - configure various params
help - print online help
ping - send ICMP ECHO_REQUEST to network host
reboot - Perform RESET of the CPU
show - show config, trace or version
verify - verify software versions
ServicesEngine boot-loader> config
IP Address [10.1.10.1] >
Subnet Mask [255.255.255.252] >
TFTP Server [192.168.1.15] >
Gateway [10.1.10.2] >
Default Helper-file [cue-vm-k9.uc500.8.6.5.pkg ] > cue-vm-k9.uc500.8.0.3.pkg
Ethernet Interface [internal] [internal] >
Default Boot [none|helper|disk] [disk] >
Default Bootloader [primary|secondary] [primary] >
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash...
64 KBdone
ServicesEngine boot-loader> boot helper
bl_boot_helper_cmd tftpboot 0x4000000 cue-vm-k9.uc500.8.0.3.pkg
Using internal device
TFTP from server 192.168.1.15; our IP address is 10.1.10.1; sending through gateway 10.1.10.2
Filename 'cue-vm-k9.uc500.8.0.3.pkg '.
Load address: 0x4000000
Loading: ########################## ########## ########## #####
done
Bytes transferred = 260703 (3fa5f hex)
bl_boot_helper_cmd root=/dev/ram rw ramdisk_size=64000 ip=10.1.10.1:192.168.1.15: 10.1.10.2: 255.255.25 5.252::eth 0:off console=ttyS0,9600 initrd=04000000,4000000 install_root=ide plat=freddo
## Booting image at 04000000 ...
Bad Magic Number
Usage:
boot <helper | disk>
Trying to reload a Cisco UC 520, CUE, only, the CF card went bad, I replaced it.
There were no backups
Using cli, I did a service-module integrated-Service-Engine 0/0 reload and confirm, then service-module integrated-Service-Engine 0/0 session
config
then boot helper
I get bad magic number, see below
I think I have the wrong PKG file, Cisco web site does not have a download for a download specifically for a 520, which is what I need , I think
Any one know where I can get one ?
ServicesEngine boot-loader>
ServicesEngine boot-loader> ?
? - alias for 'help'
boot - boot from specified src
config - configure various params
help - print online help
ping - send ICMP ECHO_REQUEST to network host
reboot - Perform RESET of the CPU
show - show config, trace or version
verify - verify software versions
ServicesEngine boot-loader> config
IP Address [10.1.10.1] >
Subnet Mask [255.255.255.252] >
TFTP Server [192.168.1.15] >
Gateway [10.1.10.2] >
Default Helper-file [cue-vm-k9.uc500.8.6.5.pkg
Ethernet Interface [internal] [internal] >
Default Boot [none|helper|disk] [disk] >
Default Bootloader [primary|secondary] [primary] >
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash...
64 KBdone
ServicesEngine boot-loader> boot helper
bl_boot_helper_cmd tftpboot 0x4000000 cue-vm-k9.uc500.8.0.3.pkg
Using internal device
TFTP from server 192.168.1.15; our IP address is 10.1.10.1; sending through gateway 10.1.10.2
Filename 'cue-vm-k9.uc500.8.0.3.pkg
Load address: 0x4000000
Loading: ##########################
done
Bytes transferred = 260703 (3fa5f hex)
bl_boot_helper_cmd root=/dev/ram rw ramdisk_size=64000 ip=10.1.10.1:192.168.1.15:
## Booting image at 04000000 ...
Bad Magic Number
Usage:
boot <helper | disk>
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
I've requested that this question be closed as follows:
Accepted answer: 0 points for jac1991's comment #a41431820
for the following reason:
Fixed the problem
Accepted answer: 0 points for jac1991's comment #a41431820
for the following reason:
Fixed the problem
The comment you selected has no information one what was done to solve it. Was the reference included in the link part of what helped you resolve this issue?
ASKER