SYN ACK
asked on
PVID 0 on HP Procurve 5412 and no untagged vlan 1
Hello,
configuration a new switch and adding ports to vlans
I am little confused with - no untagged vlan on a port - I am seeing pvid of 0 - i assume it vlan 0 and how is this different from vlan 1?
can someone explain?
and
note below - port A1 is no untagged to vlan 1 - thus defaulted to vlan 0
configuration a new switch and adding ports to vlans
I am little confused with - no untagged vlan on a port - I am seeing pvid of 0 - i assume it vlan 0 and how is this different from vlan 1?
can someone explain?
har-core-01(vlan-222)# [b]display port trunk[/b]
Interface PVID VLAN passing
A1 0 2, 10
A2 1 2, 10, 16, 40, 44, 48, 52, 81, 100, 222, 400, 630, 666
A3
A4
B1
B2 0 2, 10, 21-22, 40, 44, 48, 52, 81, 102, 222, 400, 666
B3 2 21-22, 52
B4
B5 1 2, 10, 16, 40, 44, 48, 52, 81, 100, 102, 222, 400, 630, 666
B6
B7 1 2, 10, 32, 40, 48, 52, 100, 222, 251-254, 400
and
note below - port A1 is no untagged to vlan 1 - thus defaulted to vlan 0
vlan 1
name "DEFAULT_VLAN"
no untagged
A1,B2-B4,B6,B9-B24,C1-C5,C7-C11,C13-C15,C18-C19,C22-C23,D1-D11,D13-D17,D19,D21,D24,E3,E11-E14,E16-E24,F1-F2,F7-F9,F11,F13-F24,G1,G3-G6,G9,G11-G13,G15,G17-G20,G22,G24,H1,H3-H8,H11-H24,Trk2
untagged
A2-A4,B5,B7,C6,C12,C16-C17,C20,C24,D12,D18,D20,D22-D23,E1-E2,E4-E9,F3-F6,F10,G2,G7-G8,G10,G14,G21,G23,H9-H10,Trk1
no ip address
exit
vlan 2
name "MANAGEMENT"
untagged B3,B6,B9-B13,B17-B19,B22-B23,C1,C13,D2,D19,D21,E22-E23,G5,G24,H12,H16,H19
tagged
A1-A2,B2,B5,B7,C6,C12,C16-C17,C20,C24,D12,D18,D20,D22-D23,E1-E2,E4-E9,F3-F6,F10,G2,G7-G8,G10,G14,G23,H9-H10,Trk1
ip address 172.31.2.3 255.255.255.0
exit
SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER