Solved

Sonicwall static IP setup with AT&T "Network on Demand" fiber

Posted on 2016-09-11
6
63 Views
Last Modified: 2016-09-12
Am having difficulty getting any support from AT&T for their fiber product.  Does anyone have any experience with this?

I have it connected and running fine for outbound (using DHCP), but can't find any info for how to set up static IP's in our Sonicwall so that they are usable for inbound access.
0
Comment
Question by:fuzztone65
  • 3
  • 3
6 Comments
 
LVL 6

Expert Comment

by:J Spoor
ID: 41793815
Do you have static IP's with AT&T ? As you say you are currently on DHCP.




View example configurations and the SonicWALL webui and features on http://livedemo.sonicwall.com or http://ngfw-demo.com

Multiply the effectiveness of your APT Sandbox, stop unknown and zero-day attacks at the gateway. See a demo on http://apt-demo.com or http://atp.demo.com

You can also view the Next-Generation Firewalls via
http://next-generation-firewall.com or http://next-generation-firewall-demo.com
0
 

Author Comment

by:fuzztone65
ID: 41794190
I've set up many Sonicwall's with normal static IP configurations.  The AT&T Network on Demand setup is not the same.  They don't give you your static IP range, a subnet mask and a default gateway, as I'm used to.  

Looking for someone who is familiar with that scenario.
0
 
LVL 6

Expert Comment

by:J Spoor
ID: 41794269
Sorry, not familiar with them :(
0
Find Ransomware Secrets With All-Source Analysis

Ransomware has become a major concern for organizations; its prevalence has grown due to past successes achieved by threat actors. While each ransomware variant is different, we’ve seen some common tactics and trends used among the authors of the malware.

 

Author Comment

by:fuzztone65
ID: 41794549
OK.  Got more info from AT&T.  My Sonicwall has an assigned IP that is different from our actual public static IP's.  I am supposed to set up a "NAT statement" or "NAT pool" that tells the Sonicwall where to send traffic sent to our actual public IP.  I've never had to do that.  Any ideas on where to start.  I've tried messing around with Routes and NAT policies, but no luck so far.
0
 
LVL 6

Accepted Solution

by:
J Spoor earned 500 total points
ID: 41794564
Make sure the ISP routes this secondary IP block to your WAN IP.
Then just feel free to use those IP addresses in NAT policies.

Dont' create static arp entries or routes or what soever for this secondary IP block.
Just create NAT policies.
0
 

Author Comment

by:fuzztone65
ID: 41794806
Yep, so it appears that I've got to set up new policies/rules to use the real IP's, rather than being able to tell them to use WAN1 or WAN2 (for example).  Was able to do that for testing and it worked fine.
0

Featured Post

How your wiki can always stay up-to-date

Quip doubles as a “living” wiki and a project management tool that evolves with your organization. As you finish projects in Quip, the work remains, easily accessible to all team members, new and old.
- Increase transparency
- Onboard new hires faster
- Access from mobile/offline

Join & Write a Comment

Suggested Solutions

There are two basic ways to configure a static route for Cisco IOS devices. I've written this article to highlight a case study comparing the configuration of a static route using the next-hop IP and the configuration of a static route using an outg…
In the world of WAN, QoS is a pretty important topic for most, if not all, networks. Some WAN technologies have QoS mechanisms built in, but others, such as some L2 WAN's, don't have QoS control in the provider cloud.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
This video gives you a great overview about bandwidth monitoring with SNMP and WMI with our network monitoring solution PRTG Network Monitor (https://www.paessler.com/prtg). If you're looking for how to monitor bandwidth using netflow or packet s…

759 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

19 Experts available now in Live!

Get 1:1 Help Now