Solved

3750 switch

Posted on 2016-10-11
21
21 Views
Last Modified: 2016-10-17
User Access Verification

Password:
Switch>en
Password:
Switch#show vlan

VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Fa4/0/4, Fa4/0/8, Fa4/0/9, Fa4/0/10, Fa4/0/11
                                                Fa4/0/12, Fa4/0/13, Fa4/0/14, Fa4/0/15, Fa4/0/16
                                                Gi4/0/1, Gi4/0/2, Gi4/0/3, Gi4/0/4
3    VLAN0003                         active    Fa4/0/2, Fa4/0/7
4    VLAN0004                         active    Fa4/0/17, Fa4/0/18, Fa4/0/19, Fa4/0/20, Fa4/0/21
                                                Fa4/0/22, Fa4/0/23, Fa4/0/24, Fa4/0/25, Fa4/0/26
                                                Fa4/0/27, Fa4/0/28, Fa4/0/29, Fa4/0/30, Fa4/0/31
                                                Fa4/0/32, Fa4/0/33, Fa4/0/34, Fa4/0/35, Fa4/0/36
                                                Fa4/0/37, Fa4/0/38, Fa4/0/39, Fa4/0/40, Fa4/0/41
                                                Fa4/0/42, Fa4/0/43, Fa4/0/44, Fa4/0/45, Fa4/0/46
                                                Fa4/0/47, Fa4/0/48
1002 fddi-default                     act/unsup
1003 token-ring-default               act/unsup
1004 fddinet-default                  act/unsup
1005 trnet-default                    act/unsup

VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1    enet  100001     1500  -      -      -        -    -        0      0
3    enet  100003     1500  -      -      -        -    -        0      0
4    enet  100004     1500  -      -      -        -    -        0      0
1002 fddi  101002     1500  -      -      -        -    -        0      0
1003 tr    101003     1500  -      -      -        -    -        0      0
1004 fdnet 101004     1500  -      -      -        ieee -        0      0
1005 trnet 101005     1500  -      -      -        ibm  -        0      0

Remote SPAN VLANs
------------------------------------------------------------------------------


Primary Secondary Type              Ports
------- --------- ----------------- ------------------------------------------

Switch#



where goes my fa4/0/1 and fa4/0/3-06????
0
Comment
Question by:nikunj saikia
  • 12
  • 7
  • 2
21 Comments
 
LVL 16

Expert Comment

by:Shaik M. Sajid
ID: 41839585
check show run

show run int fa4/0/1  etc.

to get the complete details
0
 

Author Comment

by:nikunj saikia
ID: 41839609
User Access Verification

Password:
Switch>en
Password:
Switch#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#no interface vlan 2
                             ^
% Invalid input detected at '^' marker.

Switch(config)#exit
Switch#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#show run fa4/0/1
                 ^
% Invalid input detected at '^' marker.

Switch(config)#do show run fa4/0/1
show run fa4/0/1
          ^
% Invalid input detected at '^' marker.

Switch(config)#do show run
Building configuration...

Current configuration : 7075 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Switch
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$6Iv5$0M76biJHWQ8.LZtZCo681/
!
no aaa new-model
clock timezone UTC 5 30
switch 4 provision ws-c3750-48ts
system mtu routing 1500
ip subnet-zero
ip routing
!
!
!
!
!
!
!
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
!
!
interface FastEthernet4/0/1
 switchport access vlan 2
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/2
 switchport access vlan 3
 switchport mode access
!
interface FastEthernet4/0/3
 switchport access vlan 2
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/4
!
interface FastEthernet4/0/5
 switchport access vlan 2
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/6
 switchport access vlan 2
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/7
 switchport access vlan 3
 switchport mode access
 switchport port-security
 --More--
0
 

Author Comment

by:nikunj saikia
ID: 41839610
it is in valn 2 but i remoned vlan 2
0
Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

 
LVL 16

Expert Comment

by:Shaik M. Sajid
ID: 41839628
yes you removed Vland 2 but still the vlan remains there in the dir of the Cisco Switch

type Dir and then check...

so you can add this ports to another Vlan and you'll see them.

or else remove vlan from the directory...
0
 
LVL 6

Expert Comment

by:Niten Kumar
ID: 41839644
Those ports were in a vlan which got deleted.  What you can do is:

Switch(config)#interface fa4/0/1
Switch (config)#switchport access vlan 1

or any other vlan as per requirement.
0
 

Author Comment

by:nikunj saikia
ID: 41839650
my interface fa4/0/1 is not working ........light dont glow when i plug it with my lappy wny???
0
 

Author Comment

by:nikunj saikia
ID: 41839652
Password:
Switch>en
Password:
Switch#show running-config
Building configuration...

Current configuration : 6886 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Switch
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$6Iv5$0M76biJHWQ8.LZtZCo681/
!
no aaa new-model
clock timezone UTC 5 30
switch 4 provision ws-c3750-48ts
system mtu routing 1500
ip subnet-zero
ip routing
!
!
!
!
!
!
!
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
!
!
interface FastEthernet4/0/1
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/2
 switchport mode access
!
interface FastEthernet4/0/3
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/4
!
interface FastEthernet4/0/5
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/6
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/7
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/8
!
interface FastEthernet4/0/9
!
interface FastEthernet4/0/10
!
interface FastEthernet4/0/11
!
interface FastEthernet4/0/12
!
interface FastEthernet4/0/13
!
interface FastEthernet4/0/14
!
interface FastEthernet4/0/15
!
interface FastEthernet4/0/16
!
interface FastEthernet4/0/17
 switchport access vlan 4
 switchport mode access
!
interface FastEthernet4/0/18
 switchport access vlan 4
 switchport mode access
 --More--
0
 

Author Comment

by:nikunj saikia
ID: 41839654
same thing happing to port 3,5,6,and 7 ........all other porta are working well except thes eports
0
 
LVL 6

Expert Comment

by:Niten Kumar
ID: 41839669
Do you need port securitu on fa4/0/1....just to troubleshoot will you be able to remove using:

Switch(config)#intetface fa4/0/1
Switch(config-if)#no switchport port-security
0
 
LVL 6

Expert Comment

by:Niten Kumar
ID: 41839675
Light does not glow because for some reason security violation has occured and port has been shutdown...to renable you have to enter

Switch(config)#interface fa4/0/1
Switch (config-if)shutdown
Switch (config-if)no shutdown
0
 

Author Comment

by:nikunj saikia
ID: 41839677
did so many times but cant sucess to remove these configurations..........in these ports
0
 
LVL 6

Expert Comment

by:Niten Kumar
ID: 41839684
Have you done the steps i have given for fa4/0/1 above....please do them and save using the command

Switch(config)#do wr

then post running config
0
 

Author Comment

by:nikunj saikia
ID: 41839707
User Access Verification

Password:
Switch>en
Password:
Switch#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int fa4/0/1
Switch(config-if)#no switchport port-security
Switch(config-if)#exit
Switch(config)#int fa4/0/1
Switch(config-if)#shutdown
Switch(config-if)#no shutdown
Switch(config-if)#exit
Switch(config)#do wr
Building configuration...
[OK]
Switch(config)#do show running-config
Building configuration...

Current configuration : 6860 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Switch
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$6Iv5$0M76biJHWQ8.LZtZCo681/
!
no aaa new-model
clock timezone UTC 5 30
switch 4 provision ws-c3750-48ts
system mtu routing 1500
ip subnet-zero
ip routing
!
!
!
!
!
!
!
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
!
!
interface FastEthernet4/0/1
 switchport mode access
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/2
 switchport mode access
!
interface FastEthernet4/0/3
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 --More--
0
 

Author Comment

by:nikunj saikia
ID: 41839708
still the same i run those command nothing happend to this fa4/0/1 port
0
 
LVL 6

Assisted Solution

by:Niten Kumar
Niten Kumar earned 500 total points
ID: 41839711
If still things are not working out for you. Is it ok for you to do a total reset of the switch? If yes then do the following:

Switch#erase startup-config
Erasing the nvram filesystem will remove all files! Continue? [confirm]y[OK]
Erase of nvram: complete
Switch#
Switch# reload


System configuration has been modified. Save? [yes/no]: n    

!--- Do not save the configuration at this prompt. Otherwise, the switch !--- reloads with the current running configuration and does not reset to default.
Proceed with reload? [confirm]y    


After switch reloads you have to remove all vlan data using the following steps:


Switch# delete flash:vlan.dat
Delete filename [vlan.dat]?

!--- Press Enter.

Delete flash:vlan.dat? [confirm]y

Switch# reload
Proceed with reload? [confirm]y
4w5d: %SYS-5-RELOAD: Reload requested


After reload all should be good if there are no hardware issues.
0
 

Accepted Solution

by:
nikunj saikia earned 0 total points
ID: 41839793
if i do that how do i telnet my switch again???
i dont have console cable right now
0
 
LVL 6

Expert Comment

by:Niten Kumar
ID: 41840004
can you do a show vlan brief and post output here
0
 
LVL 6

Expert Comment

by:Niten Kumar
ID: 41841028
Hope your issue is sorted out.
0
 

Author Comment

by:nikunj saikia
ID: 41841407
User Access Verification

Password:
Switch>en
Password:
Switch#show vlan

VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Fa4/0/1, Fa4/0/2, Fa4/0/3, Fa4/0/4, Fa4/0/5
                                                Fa4/0/6, Fa4/0/7, Fa4/0/8, Fa4/0/9, Fa4/0/10
                                                Fa4/0/11, Fa4/0/12, Fa4/0/13, Fa4/0/14, Fa4/0/15
                                                Fa4/0/16, Gi4/0/1, Gi4/0/2, Gi4/0/3, Gi4/0/4
4    VLAN0004                         active    Fa4/0/17, Fa4/0/18, Fa4/0/19, Fa4/0/20, Fa4/0/21
                                                Fa4/0/22, Fa4/0/23, Fa4/0/24, Fa4/0/25, Fa4/0/26
                                                Fa4/0/27, Fa4/0/28, Fa4/0/29, Fa4/0/30, Fa4/0/31
                                                Fa4/0/32, Fa4/0/33, Fa4/0/34, Fa4/0/35, Fa4/0/36
                                                Fa4/0/37, Fa4/0/38, Fa4/0/39, Fa4/0/40, Fa4/0/41
                                                Fa4/0/42, Fa4/0/43, Fa4/0/44, Fa4/0/45, Fa4/0/46
                                                Fa4/0/47, Fa4/0/48
1002 fddi-default                     act/unsup
1003 token-ring-default               act/unsup
1004 fddinet-default                  act/unsup
1005 trnet-default                    act/unsup

VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1    enet  100001     1500  -      -      -        -    -        0      0
4    enet  100004     1500  -      -      -        -    -        0      0
1002 fddi  101002     1500  -      -      -        -    -        0      0
1003 tr    101003     1500  -      -      -        -    -        0      0
1004 fdnet 101004     1500  -      -      -        ieee -        0      0
1005 trnet 101005     1500  -      -      -        ibm  -        0      0

Remote SPAN VLANs
------------------------------------------------------------------------------


Primary Secondary Type              Ports
------- --------- ----------------- ------------------------------------------

Switch#show vlan brief

VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Fa4/0/1, Fa4/0/2, Fa4/0/3, Fa4/0/4, Fa4/0/5
                                                Fa4/0/6, Fa4/0/7, Fa4/0/8, Fa4/0/9, Fa4/0/10
                                                Fa4/0/11, Fa4/0/12, Fa4/0/13, Fa4/0/14, Fa4/0/15
                                                Fa4/0/16, Gi4/0/1, Gi4/0/2, Gi4/0/3, Gi4/0/4
4    VLAN0004                         active    Fa4/0/17, Fa4/0/18, Fa4/0/19, Fa4/0/20, Fa4/0/21
                                                Fa4/0/22, Fa4/0/23, Fa4/0/24, Fa4/0/25, Fa4/0/26
                                                Fa4/0/27, Fa4/0/28, Fa4/0/29, Fa4/0/30, Fa4/0/31
                                                Fa4/0/32, Fa4/0/33, Fa4/0/34, Fa4/0/35, Fa4/0/36
                                                Fa4/0/37, Fa4/0/38, Fa4/0/39, Fa4/0/40, Fa4/0/41
                                                Fa4/0/42, Fa4/0/43, Fa4/0/44, Fa4/0/45, Fa4/0/46
                                                Fa4/0/47, Fa4/0/48
1002 fddi-default                     act/unsup
1003 token-ring-default               act/unsup
1004 fddinet-default                  act/unsup
1005 trnet-default                    act/unsup
Switch#
0
 

Author Comment

by:nikunj saikia
ID: 41841411
no still port 1,3,5 have some short of configuration which i want to remove without reset my switch





User Access Verification

Password:
Switch>en
Password:
Switch#show running config
                    ^
% Invalid input detected at '^' marker.

Switch#show running-config
Building configuration...

Current configuration : 6860 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Switch
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$6Iv5$0M76biJHWQ8.LZtZCo681/
!
no aaa new-model
clock timezone UTC 5 30
switch 4 provision ws-c3750-48ts
system mtu routing 1500
ip subnet-zero
ip routing
!
!
!
!
!
!
!
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
!
!
interface FastEthernet4/0/1
 switchport mode access
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/2
 switchport mode access
!
interface FastEthernet4/0/3
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/4
!
interface FastEthernet4/0/5
 switchport mode access
 switchport port-security
 switchport port-security aging time 2
 switchport port-security violation restrict
 switchport port-security aging type inactivity
 macro description cisco-desktop
 spanning-tree portfast
 spanning-tree bpduguard enable
!
interface FastEthernet4/0/6
 switchport mode access
 switchport port-security
 --More--
0
 

Author Closing Comment

by:nikunj saikia
ID: 41846345
correct
0

Featured Post

Efficient way to get backups off site to Azure

This user guide provides instructions on how to deploy and configure both a StoneFly Scale Out NAS Enterprise Cloud Drive virtual machine and Veeam Cloud Connect in the Microsoft Azure Cloud.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Even if you have implemented a Mobile Device Management solution company wide, it is a good idea to make sure you are taking into account all of the major risks to your electronic protected health information (ePHI).
When you try to share a printer , you may receive one of the following error messages. Error message when you use the Add Printer Wizard to share a printer: Windows could not share your printer. Operation could not be completed (Error 0x000006…
Internet Business Fax to Email Made Easy - With  eFax Corporate (http://www.enterprise.efax.com), you'll receive a dedicated online fax number, which is used the same way as a typical analog fax number. You'll receive secure faxes in your email, f…
Get a first impression of how PRTG looks and learn how it works.   This video is a short introduction to PRTG, as an initial overview or as a quick start for new PRTG users.

832 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question