Solved

Reg CPU & memory usage and see which is consuming more resources at that particular point of time?

Posted on 2016-10-28
13
69 Views
Last Modified: 2016-11-19
How do we be able to get the following  reports in Windows Server 2012R2 ?

 1) which process was utilized more the CPU usage from  <time:date:X>     to < time:date:Y>

2) which process was utilized more  the memory usage from time:date:X     to  time:date:Y

I am having script for getting current/present top 10 memory & CPU usage and the user using it but i need at that particular point time(i.e., means last week).Please respond ASAP
Thanks in advance!!
0
Comment
Question by:Viswanath Chilukuri
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 5
  • 4
  • 2
  • +1
13 Comments
 
LVL 95

Expert Comment

by:John Hurst
ID: 41864452
I don't think you can go backwards and get this information if you were not collecting it.

To go forward, run Performance Monitor and set up a performance log to monitor. I have normally just set up the item to monitor and let it run for an hour or two and look at the graphs that it produced.

Normally just watching Task Manager will highlight what I need.
1
 

Author Comment

by:Viswanath Chilukuri
ID: 41865773
I am having tool to get the graphs for memory/cpu usage  but i require is that i need to check which processes is consuming that much of memory /cpu at that particular time.
0
 
LVL 95

Expert Comment

by:John Hurst
ID: 41865791
Run Resource Monitor (also in Admin Tools), let it run for an hour or two. It details the processes using Disk or CPU as you choose. But you need to select a point where you can monitor it.
0
Simplifying Server Workload Migrations

This use case outlines the migration challenges that organizations face and how the Acronis AnyData Engine supports physical-to-physical (P2P), physical-to-virtual (P2V), virtual to physical (V2P), and cross-virtual (V2V) migration scenarios to address these challenges.

 
LVL 70

Expert Comment

by:Merete
ID: 41866299
Adding to John,
If you're not sure where it is  Viswanath,  nice name :)
open the task manager then Performance then below is the Resource monitor tab  this opens another window with the graphs but also the running tasks on the left you can put them side by side or just over each other
resource monitorThere is also a whole lot of settings that can be added to the task manager running processes,
at the top is the tabs put it on processes  go to the top VIEW,  last is select columns
tick memory private set and peak working set and description, right click on the high CPU and memory service. ok it and now look in the taskmanager
select columns 1taskmanager add columns
0
 
LVL 17

Expert Comment

by:Gerald Connolly
ID: 41866765
As John said, if you have not been collecting that information at the time, you will NOT be able to go back and analyse it now.
0
 

Author Comment

by:Viswanath Chilukuri
ID: 41868335
Hi Merete

Task Manager in Windows Server 2012 R2 is different we wont get option to select the Process from memory tab.Thanks for info John
0
 
LVL 95

Expert Comment

by:John Hurst
ID: 41868587
Please let us know how you make out collecting the correct information
0
 

Author Comment

by:Viswanath Chilukuri
ID: 41868611
Don't know John still i am searching multiple sites to resolve this issue,i didn't get correct info regarding this issue.As our client asked us to know which process was consumed at that particular time(its 10 days before).As that server consumes 20-25% memory normally but it consumes 70-75% for 3 hours continuously and again it consuming memory normally after 3 hrs.
Capture1.PNG
0
 
LVL 95

Expert Comment

by:John Hurst
ID: 41868619
That is a lot of CPU and Memory consumption. You should be able to determine which process is doing this from the above tools.

Also check for viruses and malware. Do a full scan.
0
 
LVL 17

Expert Comment

by:Gerald Connolly
ID: 41869443
As John and i have already said, if the system in question was not recording CPU useage on a per process basis at the time of the incident (10 days back) then it is IMPOSSIBLE to reconstruct the per process now.

All you can do is to turn on recording for the future (be aware it may apply a load on the system) so that any FUTURE events can be analysed.
0
 

Accepted Solution

by:
Viswanath Chilukuri earned 0 total points
ID: 41869944
Hi All

Thanks for yours suggestions & comments,the issue was resolved now,as i check the VM from Vcenter end their i found the VM memory is getting ballooning,as i checked all the process are consuming less memory only.only because of this ballooning the memory got less in that VM and it reached to 75%.
0
 

Author Closing Comment

by:Viswanath Chilukuri
ID: 41894061
its resolved by own
0

Featured Post

Announcing the Most Valuable Experts of 2016

MVEs are more concerned with the satisfaction of those they help than with the considerable points they can earn. They are the types of people you feel privileged to call colleagues. Join us in honoring this amazing group of Experts.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

This article summaries thoughts and ideas from two years of sustained use. It provides good reasoning to make the jump to Windows 10.
The Windows functions GetTickCount and timeGetTime retrieve the number of milliseconds since the system was started. However, the value is stored in a DWORD, which means that it wraps around to zero every 49.7 days. This article shows how to solve t…
This tutorial will walk an individual through the process of installing the necessary services and then configuring a Windows Server 2012 system as an iSCSI target. To install the necessary roles, go to Server Manager, and select Add Roles and Featu…
This Micro Tutorial will give you a basic overview of Windows DVD Burner through its features and interface. This will be demonstrated using Windows 7 operating system.

752 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question