Jim Nicolis
asked on
Cisco 887VAW NBN Bridge Mode Config
Hello,
I am switching some of our broadband connection from ADSL to NBN and with that need to put a new modem into our existing infrastructure
We are going to use a Cisco 887VAW which is compatible with the NBN network with the correct firmware for these
Can someone please take a look at my Bridge Config as its a little different to my normal ADSL ones i use on the old routers as now has the vdsl interface
I think this is right but please let me know
I have put a Management IP on vlan11 FA3 as well so i can access the until via telnet
! 887VA-BRIDGE-vDSL2-NBN-WIT H IP ON FE3
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname xxxxxx
!
logging buffered 16000
no logging console
!
boot-start-marker
boot-end-marker
!
no aaa new-model
clock timezone EST 10
! wan mode dsl
no ipv6 cef
ip source-route
no ip routing
no ip cef
!
memory-size iomem 10
crypto pki token default removal timeout 0
!
archive
log config
hidekeys
exit
exit
username xxxx privilege 15 secret 0 xxxxx
!
controller VDSL 0
operating mode vdsl2
firmware filename flash:VA_A_39h_B_38h3_24h_ j.bin
!
interface ATM0
no ip address
no ip route-cache
shutdown
no atm ilmi-keepalive
!
interface Ethernet0
no ip address
no ip route-cache
bridge-group 1
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
no ip address
!
interface FastEthernet3
no ip address
!
interface Vlan1
no ip address
no ip virtual-reassembly in
no ip route-cache
bridge-group 1
!
! Assign Switchport(s) to Existing VLAN:
Interface FastEthernet 3
switchport access vlan 11
!
! Assign IP address to VLAN11 - Managment
Interface Vlan 11
ip address 192.168.202.253 255.255.255.0
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
!
!control-plane
!
bridge 1 protocol ieee
!
line con 0
no modem enable
line aux 0
line vty 0 4
login local
transport input all
!
scheduler allocate 60000 1000
end
I am switching some of our broadband connection from ADSL to NBN and with that need to put a new modem into our existing infrastructure
We are going to use a Cisco 887VAW which is compatible with the NBN network with the correct firmware for these
Can someone please take a look at my Bridge Config as its a little different to my normal ADSL ones i use on the old routers as now has the vdsl interface
I think this is right but please let me know
I have put a Management IP on vlan11 FA3 as well so i can access the until via telnet
! 887VA-BRIDGE-vDSL2-NBN-WIT
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname xxxxxx
!
logging buffered 16000
no logging console
!
boot-start-marker
boot-end-marker
!
no aaa new-model
clock timezone EST 10
! wan mode dsl
no ipv6 cef
ip source-route
no ip routing
no ip cef
!
memory-size iomem 10
crypto pki token default removal timeout 0
!
archive
log config
hidekeys
exit
exit
username xxxx privilege 15 secret 0 xxxxx
!
controller VDSL 0
operating mode vdsl2
firmware filename flash:VA_A_39h_B_38h3_24h_
!
interface ATM0
no ip address
no ip route-cache
shutdown
no atm ilmi-keepalive
!
interface Ethernet0
no ip address
no ip route-cache
bridge-group 1
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
no ip address
!
interface FastEthernet3
no ip address
!
interface Vlan1
no ip address
no ip virtual-reassembly in
no ip route-cache
bridge-group 1
!
! Assign Switchport(s) to Existing VLAN:
Interface FastEthernet 3
switchport access vlan 11
!
! Assign IP address to VLAN11 - Managment
Interface Vlan 11
ip address 192.168.202.253 255.255.255.0
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
!
!control-plane
!
bridge 1 protocol ieee
!
line con 0
no modem enable
line aux 0
line vty 0 4
login local
transport input all
!
scheduler allocate 60000 1000
end
This question needs an answer!
Become an EE member today
7 DAY FREE TRIALMembers can start a 7-Day Free trial then enjoy unlimited access to the platform.
View membership options
or
Learn why we charge membership fees
We get it - no one likes a content blocker. Take one extra minute and find out why we block content.
ASKER
I have this Config working on Australian NBN FTTN
The only thing I added is a no shutdown on ethernet 0 as it was off after reboot
All working well now
I did have a question, I have allocated on vlan 11 as you can see an internet address so i can telnet into the unit without needing console cable which is working fine, only think i would like to know can you allocate the IP address on vlan 1 which is the bridge so i dont have to have 2 cables plugged in I am thinking no but just wanted to confirm
Adam