TAMUQITS
asked on
SCCM Available software installation Problem
We are Running SCCM 1702 and when we are publishing the software for the user so that the user can themselves visit and install the software by themselves (i.e. making the softwares available for the user's collection. Some of the softwares without any problems. However, some of the software throws the attached error.
I Have all the Boundaries and groups already verified, and everything's seems to be normal as other softwares are working fine.
Appreciate a comprehensive response.
Regards,
MBB
SCCMError.JPG
I Have all the Boundaries and groups already verified, and everything's seems to be normal as other softwares are working fine.
Appreciate a comprehensive response.
Regards,
MBB
SCCMError.JPG
ASKER
Attached is the locationservices.log file, says nothing like it.
LocationServices.log
LocationServices.log
Nothing clear in that log.
But your AD does not seem to be structured as the location shows to be "Current AD site of machine is Default-First-Site".
If you can zip and upload all the logs from this client that I should be able to find more.
But your AD does not seem to be structured as the location shows to be "Current AD site of machine is Default-First-Site".
If you can zip and upload all the logs from this client that I should be able to find more.
ASKER
Attached are the log files.
logs.zip
logs.zip
Please check this folder C:\SCCMCache\ccmcache\bq
It should have setup.exe in it. In case it does not have then you need to set the source of your application to the folder which has setup.exe in the root (Not any subfolder)
BTW, you cam copy \\tamuq-sccm\sources$\Soft ware\Minit ab18\tamuq -config.xm l to the same folder as setup.exe and change the program properties to setup.exe /config tamuq-config.xml
It should have setup.exe in it. In case it does not have then you need to set the source of your application to the folder which has setup.exe in the root (Not any subfolder)
BTW, you cam copy \\tamuq-sccm\sources$\Soft
ASKER
Tried it again with the updated settings as per above instructions, same result. Attached are the log files along with the snapshots
logs.zip
Minitab18.zip
logs.zip
Minitab18.zip
The command to install is not correct. There is no setup.exe file in that folder.
Also, by experience, the installation command is for Microsoft Office 2013 setup as shown here. https://technet.microsoft.com/en-au/library/dd630736.aspx
Does your .xml file look like this https://augustoalvarez.files.wordpress.com/2011/01/office12.png ? Please upload that.
Also, by experience, the installation command is for Microsoft Office 2013 setup as shown here. https://technet.microsoft.com/en-au/library/dd630736.aspx
Does your .xml file look like this https://augustoalvarez.files.wordpress.com/2011/01/office12.png ? Please upload that.
ASKER
I tried using the absolute path as per the MS-Office 2013 link above, gave me the same error from where I started, however, when I tried configuring the way mentioned below (Minitab18.zip), gave me the invalid command error, but it did run the setup. Also, attached the XML file as well. I have provided an updated log files as well.
Minitab18.zip
Logs.zip
Minitab18.zip
Logs.zip
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
As per the last comment, was able to install the Software Successfully.
You should first remove the content from all the DPs and after 15 minutes push it again and then re attempt installation.
Or you can create an IP range boundary for say 3-4 IP addresses which should have a test client within the range. If your content starts downloading then you need to create new boundaries as you have clients outside of your boundary range