<div>
2960-CX switch is L2 device which performing transparent bridging, that generally, means that packet is not modified as it is forwarded by switch. All manipulation with packets will have to be done after switch itself.<br />
Regarding QoS switch ports should be configured to trust CoS values, or if DCSP is used for priority - mutation maps should be configured. The easiest way would be to configure auto QoS on switch and &nbsp;to make interfaces trusted interfaces (auto qos trust).<br />
<a href="https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960cx_3650cx/software/release/15-2_3_e/configuration/guide/b_1523e_consolidated_2960cx_3560cx_cg/b_consolidated_152ex_2960-X_cg_chapter_011100.html" rel="ugc">Chapter: Configuring Auto-QoS</a>
</div>


2960-CX switch is L2 device which performing transparent bridging, that generally, means that packet is not modified as it is forwarded by switch. All manipulation with packets will have to be done after switch itself.
Regarding QoS switch ports should be configured to trust CoS values, or if DCSP is used for priority - mutation maps should be configured. The easiest way would be to configure auto QoS on switch and  to make interfaces trusted interfaces (auto qos trust).
Chapter: Configuring Auto-QoS [https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960cx_3650cx/software/release/15-2_3_e/configuration/guide/b_1523e_consolidated_2960cx_3560cx_cg/b_consolidated_152ex_2960-X_cg_chapter_011100.html]

<div>
<div class="content wysiwyg-content">
I have an inbound fiber circuit, with 5 static IP's. &nbsp;I'm using 2 (.10 &amp;&nbsp;.11), one for voice and one for data. &nbsp;Problem is, this comes through a single port from the provider's router.<br />
<br />
I have a cisco catalyst 2960-CX. &nbsp;WAN is on port 1<br />
<br />
I would like to pass all voice traffic to WAN .11, through port 7, to our host's internal router. &nbsp;This should is to be a pass through with priority &amp;&nbsp;QOS.<br />
<br />
All LAN data traffic will pass .10 through to our firewall.<br />
<br />
Which settings are necessary to accomplish this.
</div>
</div>


I have an inbound fiber circuit, with 5 static IP's.  I'm using 2 (.10 & .11), one for voice and one for data.  Problem is, this comes through a single port from the provider's router.

I have a cisco catalyst 2960-CX.  WAN is on port 1

I would like to pass all voice traffic to WAN .11, through port 7, to our host's internal router.  This should is to be a pass through with priority & QOS.

All LAN data traffic will pass .10 through to our firewall.

Which settings are necessary to accomplish this.

Configure a Cisco catalyst 2960-CX for a new SIP setup

Cisco PIX is a dedicated hardware firewall appliance; the Cisco Adaptive Security Appliance (ASA) is a firewall and anti-malware security appliance that provides unified threat management and protection the PIX does not. Other Cisco devices and systems include routers, switches, storage networking, wireless and the software and hardware for PIX Firewall Manager (PFM), PIX Device Manager (PDM) and Adaptive Security Device Manager (ASDM).

Cisco

A switch is a device that filters and forwards packets of data between LAN segments. Switches operate at the data link layer or the network layer of the Open Systems Interconnection (OSI) Reference Model and therefore support any packet protocol. LANs that use switches to join segments are called switched LANs or, in the case of Ethernet networks, switched Ethernet LANs. A hub is a connection point for devices in a network. Hubs are commonly used to connect segments of a LAN. A hub contains multiple ports; when a packet arrives at one port, it is copied to the other ports so that all segments of the LAN can see all packets.