• Status: Solved
  • Priority: High
  • Security: Public
  • Views: 58
  • Last Modified:

Cisco AP 1224

I am trying to understand why I don't see the actual configuration when I access the AP via the GUI. in CLI, I can see Radius, TACACS, and other good stuffs. But on the GUI, all I see is the IP address of bvi1. Thanks
0
leblanc
Asked:
leblanc
  • 6
  • 4
3 Solutions
 
Craig BeckCommented:
Can you screenshot the GUI and post here, please?
0
 
leblancAccountingAuthor Commented:
There are a lot of GUIs. But I include this one with the Radius server. Radius server is configured and I can see it in CLI. But the GUI shows nothing. I have never dealt with Cisco AP but this is strange.
aaa new-model
!
!
aaa group server radius rad_eap
 server 10.10.10.240 auth-port 1645 acct-port 1646
!
aaa group server radius rad_mac
 server 10.10.10.240 auth-port 1645 acct-port 1646
!
aaa group server radius rad_acct
 server 10.10.10.240 auth-port 1645 acct-port 1646
!
aaa group server radius rad_admin
 cache expiry 1
 cache authorization profile admin_cache
 cache authentication profile admin_cache

Open in new window



pic
0
 
Craig BeckCommented:
It's a code issue. The web code hasn't parsed the config properly. It's a common issue on autonomous APs when you config via CLI.
0
WEBINAR: 10 Easy Ways to Lose a Password

Join us on June 27th at 8 am PDT to learn about the methods that hackers use to lift real, working credentials from even the most security-savvy employees. We'll cover the importance of multi-factor authentication and how these solutions can better protect your business!

 
leblancAccountingAuthor Commented:
So my AP was configured in CLI. That is why I could not see in the GUI. Correct?

I need to config another AP with the same type of setup. It is straightforward, except I don't know what to configure for the channel number under the radio interface. Below is a snapshot of the config of the existing working AP and the channel is set to 2437. The other config has it as 5240. So I am not sure what I need to configure for this new one.
...
interface Dot11Radio0
 no ip address
 no ip route-cache
 !
 encryption vlan 100 mode ciphers aes-ccm tkip 
 !
 ssid MYSSID
 !
 antenna transmit right
 antenna receive right
 antenna gain 2
 channel 2437
 station-role root

Open in new window

0
 
Craig BeckCommented:
2437 is a 2.4GHz channel, so that's configured on interface Dot11Radio0. 5240 is a 5GHz channel, so configured on Dot11Radio1.

You can configure any channel available on the radio interfaces... Just check the syntax for the channel command by hitting ? at the CLI.

You should really only use 2412, 2437 and 2462 for the radio0 interface though (channels 1, 6 and 11).
0
 
Craig BeckCommented:
... And yes, config via CLI often breaks the GUI bit. Strange but true.
0
 
leblancAccountingAuthor Commented:
AP(config-if)#channel ?
  <1-2462>         One of: 1 2 3 4 5 6 7 8 9 10 11 2412 2417 2422 2427 2432
                   2437 2442 2447 2452 2457 2462
  least-congested  Scan for best frequency


How do you know 2412, 2437 and 2462 is channel 1, 6, & 11?
0
 
Craig BeckCommented:
Channel 1 is 2412.  Each channel then increments by 5MHz, so channel 2 is 2417, channel 3 is 2422, etc.
0
 
leblancAccountingAuthor Commented:
Ahhh... I see. I learn something new about wireless today. Thank you.
1
 
Craig BeckCommented:
My pleasure :-)
0
Question has a verified solution.

Are you are experiencing a similar issue? Get a personalized answer when you ask a related question.

Have a better answer? Share it in a comment.

Join & Write a Comment

Featured Post

Protect Your Employees from Wi-Fi Threats

As Wi-Fi growth and popularity continues to climb, not everyone understands the risks that come with connecting to public Wi-Fi or even offering Wi-Fi to employees, visitors and guests. Download the resource kit to make sure your safe wherever business takes you!

  • 6
  • 4
Tackle projects and never again get stuck behind a technical roadblock.
Join Now