Unable to create HSRP channel between Cisco Catalyst 2970G and Cisco Catalyst 3850

I am trying to create an HSRP channel between a Cisco Catalyst 2970G and a Cisco Catalyst 3850. The port (Gi0/10) on the 2970G is shown as suspended (LEDs are amber). The port (Te1/0/14) on the 3850 is shown as not connected (though the LEDs are green).

For both the 3850 and the 2970G, I have included the output of sh vtp status, the port configuration, and the output of the interface status (sh int te1/0/14). On the 2970G, I have also included the output of sh log that reflect a VTP domain mismatch.

Cisco 3850

US04SW21(config-if)#do sh vtp status
VTP Version capable             : 1 to 3
VTP version running             : 1
VTP Domain Name                 : US04SW21
VTP Pruning Mode                : Disabled
VTP Traps Generation            : Enabled
Device ID                       : 00a2.89ac.ff00
Configuration last modified by 172.18.0.21 at 0-0-00 00:00:00

Feature VLAN:
--------------
VTP Operating Mode                : Transparent
Maximum VLANs supported locally   : 1005
Number of existing VLANs          : 16
Configuration Revision            : 0
MD5 digest                        : 0xC3 0xB5 0xAD 0x04 0xF4 0x5A 0x96 0xC4
                                    0x7D 0xE0 0x0C 0x4F 0x0E 0xA5 0xBB 0x48


interface TenGigabitEthernet1/0/14
 switchport mode trunk
 speed 1000
 duplex full
 channel-group 1 mode active
end

US04SW21(config)#do sh int te1/0/14
TenGigabitEthernet1/0/14 is down, line protocol is down (notconnect)
  Hardware is Ten Gigabit Ethernet, address is 00a2.89ac.ff0e (bia 00a2.89ac.ff0e)
  MTU 1500 bytes, BW 10000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive not set
  Full-duplex, 1000Mb/s, link type is auto, media type is unknown
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 5 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out



Cisco Catalyst 2970G

rlmdcswitch2#sh vtp status
VTP Version                     : 2
Configuration Revision          : 0
Maximum VLANs supported locally : 1005
Number of existing VLANs        : 12
VTP Operating Mode              : Transparent
VTP Domain Name                 : RLMDCSWITCH2
VTP Pruning Mode                : Disabled
VTP V2 Mode                     : Disabled
VTP Traps Generation            : Enabled
MD5 digest                      : 0x97 0x4A 0x5D 0x4D 0xCE 0x5A 0xD8 0x87
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00

interface GigabitEthernet0/10
 switchport trunk encapsulation dot1q
 switchport mode trunk
 duplex full
 speed 1000
 channel-group 1 mode active
end

GigabitEthernet0/10 is up, line protocol is down (suspended)
  Hardware is Gigabit Ethernet, address is 0018.736f.f90a (bia 0018.736f.f90a)
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:13, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     41435 packets input, 3311470 bytes, 0 no buffer
     Received 41435 broadcasts (0 multicast)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 41400 multicast, 0 pause input
     0 input packets with dribble condition detected
     446306 packets output, 31636314 bytes, 0 underruns
     0 output errors, 0 collisions, 9 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out


       Syslog logging: enabled (0 messages dropped, 2 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
    Console logging: disabled
    Monitor logging: disabled
    Buffer logging: level debugging, 126 messages logged, xml disabled,
                    filtering disabled
    Exception Logging: size (4096 bytes)
    Count and timestamp logging messages: disabled
    File logging: disabled
    Trap logging: level informational, 129 message lines logged
        Logging to 172.18.4.98, 129 message lines logged, xml disabled,
               filtering disabled

Log Buffer (4096 bytes):
000093: *Mar  1 19:04:29.487 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/11, changed state to up
000094: *Mar  1 19:04:37.808 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/10, changed state to up
000095: *Mar  1 19:04:40.023 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
000096: *Mar  1 19:04:55.189 UTC: %DTP-5-DOMAINMISMATCH: Unable to perform trunk negotiation on port Gi0/10 because of VTP domain mismatch.
000097: *Mar  1 19:04:58.083 UTC: %DTP-5-DOMAINMISMATCH: Unable to perform trunk negotiation on port Gi0/11 because of VTP domain mismatch.
000098: *Mar  1 19:05:07.823 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
000099: *Mar  1 19:05:49.120 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
000100: *Mar  1 19:05:50.151 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/11, changed state to down
000101: *Mar  1 19:05:51.133 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/10, changed state to down
000102: *Mar  1 19:05:51.150 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
000103: *Mar  1 19:05:52.156 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/10, changed state to down
000104: *Mar  1 19:06:20.904 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/10, changed state to up
000105: *Mar  1 19:06:28.370 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/11, changed state to up
000106: *Mar  1 19:06:32.740 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/10, changed state to up
000107: *Mar  1 19:06:39.619 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to up
000108: *Mar  1 19:06:49.660 UTC: %DTP-5-DOMAINMISMATCH: Unable to perform trunk negotiation on port Gi0/10 because of VTP domain mismatch.
000109: *Mar  1 19:06:57.009 UTC: %DTP-5-DOMAINMISMATCH: Unable to perform trunk negotiation on port Gi0/11 because of VTP domain mismatch.
000110: *Mar  1 19:07:02.755 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
000111: *Mar  1 19:11:11.494 UTC: %PHY-4-EXCESSIVE_ERRORS: Excessive FCS, data, or idle word errors found on interface Gi0/10
000112: *Mar  1 19:24:24.091 UTC: %LINK-5-CHANGED: Interface GigabitEthernet0/10, changed state to administratively down
000113: *Mar  1 19:24:25.098 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/10, changed state to down
000114: *Mar  1 19:24:27.220 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
000115: *Mar  1 19:24:28.202 UTC: %LINK-5-CHANGED: Interface GigabitEthernet0/11, changed state to administratively down
000116: *Mar  1 19:24:29.208 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/11, changed state to down
000117: *Mar  1 19:24:45.189 UTC: %EC-5-ERRPROT: Channel protocol mismatch for interface Gi0/10 in group 1: the interface can not be added to the channel group
000118: *Mar  1 19:25:49.622 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/10, changed state to down
000119: *Mar  1 19:25:52.012 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/11, changed state to down
000120: *Mar  1 19:25:52.021 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/10, changed state to up
000121: *Mar  1 19:25:54.454 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/11, changed state to up
000122: *Mar  1 19:26:01.584 UTC: %EC-5-L3DONTBNDL2: Gi0/10 suspended: LACP currently not enabled on the remote port.
000123: *Mar  1 19:26:04.100 UTC: %EC-5-L3DONTBNDL2: Gi0/11 suspended: LACP currently not enabled on the remote port.
000124: *Mar  1 19:26:20.685 UTC: %DTP-5-DOMAINMISMATCH: Unable to perform trunk negotiation on port Gi0/10 because of VTP domain mismatch.
000125: *Mar  1 19:26:22.983 UTC: %DTP-5-DOMAINMISMATCH: Unable to perform trunk negotiation on port Gi0/11 because of VTP domain mismatch.
000126: *Mar  1 19:28:39.206 UTC: %SYS-5-CONFIG_I: Configured from console by rlmdcswitch2 on console

From the output of sh vtp status, I see that there are different VTP versions between the switches. I also see that from the output of the log, the 3850 does not have LACP enabled.

Any assistance is greatly appreciated.
LVL 3
djhathAsked:
Who is Participating?

[Product update] Infrastructure Analysis Tool is now available with Business Accounts.Learn More

x
I wear a lot of hats...

"The solutions and answers provided on Experts Exchange have been extremely helpful to me over the last few years. I wear a lot of hats - Developer, Database Administrator, Help Desk, etc., so I know a lot of things but not a lot about one thing. Experts Exchange gives me answers from people who do know a lot about one thing, in a easy to use platform." -Todd S.

Soulja53 6F 75 6C 6A 61 Commented:
If you mean a port-channel, you have to use the same interface speeds.  1G to 1G or 10g to 10g.
0
djhathAuthor Commented:
Yes. Both ports are hard-coded to speed 1000 / duplex full.
0
Soulja53 6F 75 6C 6A 61 Commented:
You can't down grade a 10g interface to 1g. If you look at the speed of your 10g above, even with your speed 1000 command under it, the interface is still running at 10g.
0
Get Cisco Certified in IT Security

There’s a high demand for IT security experts and network administrators who can safeguard the data that individuals, corporations, and governments rely on every day. Pursue your B.S. in Network Operations and Security and gain the credentials you need for this high-growth field.

Soulja53 6F 75 6C 6A 61 Commented:
Sorry I misread the above output. I believe it is a result of interface incompatibility. Someone can correct me justincase I am wrong.  ;)
1
JustInCaseCommented:
DTP is relevant in the case that trunk should be negotiated (vtp domain names and passwords must match).
On both  switches
vtp domain <MyDomain>
vtp password <MyPassword>
vtp version 2


sh int te1/0/14
 media type is unknown <-- is this GLC-T (since there is no input or output traffic I guess GLC-T may not be supported in IOS or incompatible)?

Please verify compatibility of GLC-T compatibility - Compatibility Information
In some IOS versions there is bug that 10Gb ports do not work properly with 1Gb GLC-Ts.

Gi0/10 suspended: LACP currently not enabled on the remote port.
Looks like port is suspended until other side starts to send LACP packets. However since there is no traffic input or output on 3850 interface, I guess it will not happen.
0

Experts Exchange Solution brought to you by

Your issues matter to us.

Facing a tech roadblock? Get the help and guidance you need from experienced professionals who care. Ask your question anytime, anywhere, with no hassle.

Start your 7-day free trial
djhathAuthor Commented:
I ended up swapping cables and swapping ports on the 3850 and all the ports show as connected. However, when I run sh standby br, it comes up as blank.
0
JustInCaseCommented:
Did you configure standby?  I see just trace of etherchannel configuration.
0
Soulja53 6F 75 6C 6A 61 Commented:
@djhath

you are confusing port channels with HSRP. They are totally different.
0
nociSoftware EngineerCommented:
HSRP is about having 2 routers act in tandem on one IP address, so there is failover in case one router dies.

Portchannel is 2 ports on a switch acting as ONE port, and they need to have the same specs. comming from one switch (-stack).

So two completely different concepts.
0
WissamSenior Network EngineerCommented:
2970 series switches are just layer-2 switches and do not support HSRP.
0
It's more than this solution.Get answers and train to solve all your tech problems - anytime, anywhere.Try it for free Edge Out The Competitionfor your dream job with proven skills and certifications.Get started today Stand Outas the employee with proven skills.Start learning today for free Move Your Career Forwardwith certification training in the latest technologies.Start your trial today
Cisco

From novice to tech pro — start learning today.